A gray metal shop with a silver roof on a gravel lot, the roll-up door open on a welding table, red toolboxes and a chain hoist, a walk-in door beside the bay, and an older red utility tractor with no cab. A hay field with round bales, a board fence and a fall tree line sit behind.

Gearboxes, hydraulics and cracked frames fixed between cuttings.

A Casey County shop that welds, machines and rebuilds farm equipment of every make, and drives out to the hay field when it can't come to us.

Open six days in hay season (demo).

Liberty shop

I grew up keeping our hay equipment running between cuttings. Gearboxes, hoses, a deck that cracked on a rock. After twenty years in a factory tool room I opened this shop in Liberty so the farms around here would have a place that welds, machines and rebuilds every make, and comes to the field when the machine will not make the trip.

Shop and field

Repairs

A welder in an auto-darkening helmet, brown leather gloves, a tan leather jacket and work boots MIG-welds a cracked steel implement frame on a low welding table. Sparks fall to the floor. The welding machine sits on a wheeled cart with its gas cylinder chained on, an amber screen stands beside him, and the open roll-up door shows a green field.

Welding

A cracked loader bucket, a broken hitch or a cutter deck that split on a rock is everyday work. We weld steel frames, brackets and buckets on the bench, helmet down, sparks to the floor.

If the implement is too large or too broken to haul, the welder goes to the farm. We look at the crack first and tell you whether it is a patch or a new piece.

See welding rates
An opened orange-red implement gearbox on a steel bench with the gears showing. On a gray shop rag beside it are two tapered roller bearings, two seals, a gasket and a small tray of bolts, with a ratchet to the side.

Gearboxes

Cutter, tedder and post-hole gearboxes usually fail the same way. A seal weeps, a bearing growls, then a gear goes.

We open the case on the bench, lay out the bearings and seals, and call you with the parts price before anything is ordered.

See gearbox rates
A machinist in safety glasses and a navy shirt checking a short steel shaft against a steel rule on a separate workbench, with a stopped lathe behind her.

Machining

When a pin, bushing or shaft is no longer sold, we turn it. The lathe, mill and drill press stay busy making the odd part that keeps an older machine in the field.

We measure twice and call before we cut steel you did not ask for. Nobody wears gloves at a spinning lathe.

See shop rates
A young mechanic in clear safety glasses, a gray long-sleeve shirt and black work gloves sets a steel fitting on a black hydraulic hose in a bench-mounted hose crimper. A tray of steel fittings sits on the bench and reels of black hose stand on a rack behind him.

Hydraulics

A blown hose does not have to end the cutting. We cut and crimp hydraulic hoses while you wait, and we reseal cylinders when the rod is still straight.

Bring the old hose or the cylinder, or we will come measure it in the field and make the hose on the truck.

See hydraulic rates

Work orders

Rates

Prices below are demo prices for this template. We still call with a number before parts are ordered.

NO. 01

Shop labor, all makes

Hourly work in the shop, old machines and new.

$98 an hour

Demo price

NO. 02

Field service call within 25 miles

Then $4.50 a mile. Shop labor is extra on site.

$135

Demo price

NO. 03

Welding and frame repair

Cracked decks, frames, loader buckets and hitches.

From $120

Demo price

NO. 04

Gearbox reseal and bearings

Cutter, tedder and post-hole gearboxes. Parts are extra.

From $385

Demo price

NO. 05

Hydraulic hoses made while you wait

Cut and crimped in the shop or on the truck.

From $55 each

Demo price

NO. 06

Hydraulic cylinder reseal

Seal kit is extra. We call before we order it.

From $165

Demo price

NO. 07

Worn pivot pins and bushings

Replaced here, with line boring on site.

From $225 a pivot

Demo price

NO. 08

Pickup and delivery on our trailer

Loaded miles. $75 minimum.

$5 a loaded mile

Demo price

Parts are billed at cost plus handling, and we call before ordering anything over $100 (demo).

A white pickup with a gray utility body and a small crane parked in a cut hay field beside a green round baler that sits unhitched on its tongue jack. A mechanic in a cap and leather gloves kneels at the baler's pickup reel. Windrows, round bales and wooded hills are behind.

On the farm

Field calls

The truck carries a welder, a hose crimper, a small crane and the hoses, seals, pins and tines we use most. If the part is on the truck, we fix it in the field. If it is not, we say so before we leave the shop.

Have the machine shut off, the key out, and sitting on level ground. Lower the implement. Do not leave a loader or a cutter hanging in the air. If it is not safe to be near, say that when you call.

A field call inside 25 miles is $135, then $4.50 a mile past that, plus shop labor on site. Demo price. We call before we roll if the job sounds bigger than a hose or a tine.

Request a field call

From a customer

The rotary cutter gearbox quit in the middle of the second field. They resealed it and I was mowing again two days later.

Helen, Columbia

The order of work

How it works

  1. Step 1. Call or send the form with a photo.

  2. Step 2. Bring it in, or we pick it up or come to you.

  3. Step 3. We find the problem and call with a price before ordering parts.

  4. Step 4. We fix it, test it and call when it is ready.

Before anyone is under it

Before you bring it

  • Lower every implement to the ground and shut the tractor off before anyone works near it.
  • Take the key.
  • Never get under a raised loader or cutter that is not blocked.
  • Let hydraulics and gearboxes cool.
  • Wash off the worst of the mud and grass so we can see the crack.

Not sure it's safe to drive over? Call (606) 555-0193 and we'll come get it.

The owner, a broad man in his early 60s with a short gray beard, a cap and a faded denim shirt, points at the wear on an old steel pivot pin on a steel bench. A farmer in her 40s, in a canvas barn coat and jeans, listens beside a new bronze bushing. A manual lathe, red toolboxes and a pegboard of hand tools are behind them.
Old pin, new bushing.

The crew

The shop

It is a small crew: the owner, a machinist and a mechanic. No dealer sign, no last names on the door. We work on all makes, old and new, and we would rather rebuild a gearbox than tell you the machine is done.

Parts for older iron are often gone from the shelf. When that happens we measure the worn pin or the broken bracket and make what the old part called for, or we find a seal kit that fits and tell you the price before we order it.

Around Lake Cumberland

Towns served

Liberty and the hay and cattle farms through Casey, Russell, Adair, Lincoln and Pulaski Counties. Field calls run about 25 miles, then by the mile.

  • Liberty
  • Russell Springs
  • Jamestown
  • Columbia
  • Hustonville
  • Eubank
  • Somerset
  • Casey County
  • Russell County
  • Adair County
  • Lincoln County
  • Pulaski County

Demo answers

Questions

Start a job

Bring it in

Work order

Tell us the machine and what quit. We call back the same day.

Machine
How it gets here

Optional. The photo stays in this browser. Nothing is uploaded.

Broke down in the field? Call (606) 555-0193